This change removes the assumption that a frame will always have
a src set on it. This assumption is incorrect.
Given a scenario where an RTP packet is received with no payload
the resulting audio frame will have no samples. If this frame goes
through a signed linear translation path an interpolated frame can
be created (if generic packet loss concealment is enabled) that has
minimal data on it, including no src. If this frame is given to a
translation path a crash will occur due to the lack of src.
ASTERISK-28499
Change-Id: I024d10dd98207eb8a6b35b59880bcdf1090538f8
After receiving a 200 OK with a declined stream in response to a T.38
initiated re-invite Asterisk would crash when attempting to dereference
a NULL session media object.
This patch checks to make sure the session media object is not NULL before
attempting to use it.
ASTERISK-28495
patches:
ast-2019-004.patch submitted by Alexei Gradinari (license 5691)
Change-Id: I168f45f4da29cfe739acf87e597baa2aae7aa572
res_pjsip_mwi allows both solicited and unsolicited MWI subscription types.
While both can be set in the configuration for a given endpoint/aor, only
one is allowed. Precedence is given to unsolicited. Meaning if an endpoint/aor
is configured to allow both types then the solicited subscription is rejected
when it comes in. However, there is a configuration option to override that
behavior:
mwi_subscribe_replaces_unsolicited
When set to "yes" then when a solicited subscription comes in instead of
rejecting it Asterisk is suppose to replace the unsolicited one if it exists.
Prior to this patch there was a bug in Asterisk that allowed the solicted one
to be added, but did not remove the unsolicited. As a matter of fact a new
unsolicited subscription got added everytime a SIP register was received.
Over time this eventually could "flood" a phone with SIP notifies.
This patch fixes that behavior to now make it work as expected. If configured
to do so a solicited subscription now properly replaces the unsolicited one.
As well when an unsubscribe is received the unsolicited subscription is
restored. Logic was also put in to handle reloads, and any configuration changes
that might result from that. For instance, if a solicited subscription had
previously replaced an unsolicited one, but after reload it was configured to
not allow that then the solicited one needs to be shutdown, and the unsolicited
one added.
ASTERISK-28488
Change-Id: Iec2ec12d9431097e97ed5f37119963aee41af7b1
Current implementation of ast_channel_tech send_digit_begin hook uses
same function for tone playback as key press handler. This cause every
incoming dtmf send back to asterisk. In case of two unistim phones
connected to each other, it'll cause indefinite DTMF loop. Fix add
separate function for dtmf tone phone play.
Change-Id: I5795db468df552f0c89c7576b6b3858b26c4eab4
This patch fixes one-way oudio that users expirienced on
big-endian architechtires. RTP port number bytes was stored
in improper order and phone sent RTP to wrong RTP port.
Reported-by: Andrey Ionov
Change-Id: I9a9ca7f26e31a67bbbceff12923baa10dfb8a3be
The UnicastRTP channel driver provided by chan_rtp now accepts
"<hostname>:<port>" as an alternative to "<ip_address>:<port>"
in the destination. The first AAAA (preferred) or A record resolved
will be used as the destination. The lookup is synchronous so beware
of possible dialplan delays if you specify a hostname.
Change-Id: Ie6f95b983a8792bf0dacc64c7953a41032dba677
The new function takes in a pointer to an ast_sockaddr structure,
a hostname and an optional port and then dispatches parallel
"AAAA" and "A" record queries. If an "AAAA" record is returned,
it's parsed into the ast_sockaddr structure along with the port
if it was supplied. If no "AAAA" record was returned, the
first "A" record returned (if any) is parsed instead.
This is a synchronous call. If you need asynchronous lookups,
use ast_dns_query_set_resolve_async and roll your own.
Change-Id: I194b0b0e73da94b35cc35263a868ffac3a8d0a95
NEC SIP Station interface with authenticated registration only supports cnonce
up to 32 characters. In Linux, PJSIP would generate 36 character cnonce
which included hyphens. Teluu developed this patch adding a compile time
setting to default to not include the hyphens. They felt it best to still
generate the UUID and strip the hyphens.
They have indicated it will be part of PJSIP 2.10.
ASTERISK-28509
Reported-by: Dan Cropp
Change-Id: Ibdfcf845d4f8c0a14df09fd983b11f2d72c5f470
Given the following request path and 2 handler paths...
Request: /channels/externalMedia
Handler: /channels/{channelId} "wildcard"
Handler: /channels/externalmedia "non-wildcard"
...if /channels/externalMedia was registered as a handler after
/channels/{channelId} as shown above, the request would automatically
match the wildcard handler and attempt to parse "externalMedia" into
the channelId variable which isn't what was intended. It'd work
if the non-wildard entry was defined in rest-api/api-docs/channels.json
before the wildcard entry but that makes the json files
order-dependent which isn't a good thing.
To combat this issue, the search loop saves any wildcard match but
continues looking for exact matches at the same level. If it finds
one, it's used. If it hasn't found an exact match at the end of
the current level, the wildcard is used. Regardless, after
searching the current level, the wildcard is cleared so it won't
accidentally match for a different object or a higher level.
BTW, it's currently not possible for more than 1 wildcard entry
to be defined for a level. For instance, there couldn't be:
Handler: /channels/{channelId}
Handler: /channels/{channelName}
We wouldn't know which one to match.
Change-Id: I574aa3cbe4249c92c30f74b9b40e750e9002f925
There are 4 scenarios to consider when capturing audio from a channel
with an audiohook:
1. There is no rx and no tx audio, so return nothing.
2. There is rx but no tx audio, so return rx.
3. There is tx but no rx audio, so return tx.
4. There is rx and tx audio, so mix them and return.
The file passed as the primary argument to MixMonitor will be written to
in scenarios 2, 3, and 4. However, if you pass the r() and t() options
to MixMonitor, a frame will only be written to the r() file if there was
rx audio and a frame will only be written to the t() file if there was
tx audio.
If you subsequently take the r() and t() files and try to mix them, the
sides of the conversation will 'drift' and be non-representative of the
user experience.
This patch adds a new 'S' option to MixMonitor that injects a frame of
silence on either the r() side or the t() side of the channel so that
when later mixed, there is no such drift.
Change-Id: Ibf5ed73a811087727bd561a89a59f4447b4ee20e
In chan_sip, there was variable SIPFROMDOMAIN that allows to set
From header URI domain per channel. This patch introduces res_pjsip
variable SIPFROMDOMAIN for backward compatibility with chan_sip.
ASTERISK-28489
Change-Id: I715133e43172ce2a1e82093538dc39f9e99e5f2e
The function leave_voicemail checks if expungeonhangup is set,
but does not check if IMAP stream is closed,
so it could call imap function with NULL stream.
This leads to segfault.
ASTERISK-28505 #close
Change-Id: Ib66c57c1f1ba97774e447b36349198e2626a8d7c
Because keypad() is exported by libtinfo, it needs to be explicitly
added to the linker options.
ASTERISK-28487 #close
Change-Id: I6c2ad5b95f422c263d078b5c0e84c111807dffc6
Somehow it's possible for the srtp session object to be NULL even though the
Asterisk srtp object itself is valid. When this happened it would cause a
crash down in the srtp code when attempting to protect or unprotect data.
After looking at the code there is at least one spot that makes this situation
possible. If Asterisk fails to unprotect the data, and after several retries
it still can't then the srtp->session gets freed, and set to NULL while still
leaving the Asterisk srtp object around. However, according to the original
issue reporter this does not appear to be their situation since they found
no errors logged stating the above happened (which Asterisk does for that
situation).
An issue was found however, where a possible race condition could occur between
the pjsip incoming negotiation, and the receiving of RTP packets. Both places
could attempt to create/setup srtp for the same rtp instance at the same time.
This potentially could be the cause of the problem as well.
Given the above this patch adds locking around srtp setup for a given rtp, or
rtcp instance. NULL checks for the session have also been added within the
protect and unprotect functions as a precaution. These checks should at least
stop Asterisk from crashing if it gets in this situation again.
This patch also fixes one other issue noticed during investigation. When doing
a replace the old object was freed before creating the replacement. If the new
replacement object failed to create then the rtp/rtcp instance would now point
to freed srtp data which could potentially cause a crash as well when the next
attempt to reference it was made. This is now fixed so the old srtp object is
kept upon replacement failure.
Lastly, more logging has been added to help diagnose future issues.
ASTERISK-28472
Change-Id: I240e11cbb1e9ea8083d59d50db069891228fe5cc
To make throttling by label fully active, the "throttle" option
has to be specified with a specific label.
You can now specify "skip_gate" in the Gerrit comments when you
do a +2 code review to tell Jenkins not to actually run the
gate. You'd do this if you plan to manually merge the change.
Also updated the "printenv" debug output to better sort multi-line
comments.
Change-Id: I4c0b1085acec4805f2ca207eebac50aad81f27e2
When updating times on CDR or CEL records using the time at which
it is done can result in times being incorrect if the system is
heavily loaded and stasis message processing is delayed.
This change instead makes it so CDR and CEL use the time at which
the stasis messages that drive the systems are created. This allows
them to be backed up while still producing correct records.
ASTERISK-28498
Change-Id: I6829227e67aefa318efe5e183a94d4a1b4e8500a
Originally, the eligible nodes for a job were labelled only by
"swdev-docker". So basically any node could run any job. We had
found that allowing a node to run more than 1 gate at a time was
problematic so we limited the nodes to processing 1 job at a time.
With the creation of the Asterisk 17 branches however, we now have
so many active branches that getting checks and gates through in
a timely manner is problematic when a node can run only 1 job
at a time.
Now the nodes are also labelled by the job type they can run.
For instance: "asterisk-check", "asterisk-gate", etc. With the
"Throttle Concurrent Builds" plugin, we can now allow a node to
run more than 1 job BUT throttle by job type. For instance:
Allow 2 jobs but only 1 asterisk-gate at a time.
Now a node can run 2 checks or 1 check and 1 gate or 1 gate but
not 2 gates at a time.
Change-Id: I2032bf6afbcec5c341d9b852214c0c812d3d6db5
You now select voicemail backends like normal dialplan applications, so
there is no longer a need for their own menuselect category.
Reported by snuff-work in #asterisk-dev
Change-Id: Idfa4c9c8349726074318a9e6b68d24c374521005
There were still a few places in the code that could overflow when "packing"
a json object with a value outside the base type integer's range. For instance:
unsigned int value = INT_MAX + 1
ast_json_pack("{s: i}", value);
would result in a negative number being "packed". In those situations this patch
alters those values to a ast_json_int_t, which widens the value up to a long or
long long.
ASTERISK-28480
Change-Id: Ied530780d83e6f1772adba0e28d8938ef30c49a1
The code for gathering contacts could result in the same contact
being retrieved and added to the list multiple times. The container
which stores the contacts to display will now only allow a contact
to be added to it once instead of multiple times.
ASTERISK-28228
Change-Id: I805185cfcec03340f57d2b9e6cc43c49401812df
incorrect handling of UDPTL squence number wrap arounds causes
loss of packets every time the wrap around occurs
ASTERISK-28483 #close
Change-Id: I33caeb2bf13c574a1ebb81714b58907091d64234
The functions that build manager message headers do so in a way that
results in a single messages being split across multiple packets. While
this doesn't matter to the remote end, it makes network captures noisier
and harder to follow, and also means additional system calls.
With this patch, we build up more of the message content into the TLS
buffer before flushing to the network. This change is completely
internal to the manager code and does not affect any of the existing
API's consumers.
Change-Id: I50128b0769060ca5272dbbb5e60242d131eaddf9
When a module fails to register itself (usually a coding error
in the module), dlerror() can return NULL. We weren't checking
for that in load_dlopen() before trying to strdup the error message
so a SEGV was thrown. dlerror() is now surrounded with an S_OR
so we don't SEGV.
Change-Id: Ie0fb9316f08a321434f3f85aecf3c7d2ede8b956
